GEN II Lip Light - Red

  • Gen II lip light with red LED for Bose headset
  • Gen II lip light with red LED for Bose headset
  • Flitelite Gen II lip light with red LED for Bose aviator headset
  • Flitelite GEN II lip light with red LED for Lightspeed aviation headset
  • Side view of Flitelite Gen II lip light with red LED for David Clark aviation headset
  • View of Flitelite Gen II lip light rear sensor for turning light on and off
  • Close up view of the rear sensor on the Gen II lip light for aviation headsets
  • Gen II dual sensor lip light with red LED for Lightspee aviation headsets
  • Black nylon dual AA batttery pack
  • Black polymer coin cell battery pack for aviator lip lights


GEN II Lip Light - Red


FLITELite GEN II Dual Sensor Pilot Light. Red Light.  Designed to protect peripheral night vision, perfect for the General Aviation Cockpit.

FLITELite comes complete with: 

  • Red Lip Light - for use with compatibility for legacy red colored aircraft
    • Headset or Helmet Adapter (new adapters are free, only shipping is charged)
    • Choice of Battery Pack:
    • 2 Cell AAA Polymer Battery Pack
    • 2 Cell Nylon AA Battery Pack
    • CR2032 Coin Cell Pack (CR2032 battery not included)
    • Attachment accessories
    • AAA Batteries
    • Warranty

    Designed to match the red used in GA aircraft.   Civilian aircrew that fly with Bose, David Clark, or Lightspeed headsets will appreciate the custom fit of the FLITELite adapter system.
    GEN II accommodates pilots with headsets with shorter booms with incorporation of an 11 degree light angle. Longer booms can easily put the light in the proper position, now shorter booms can as well.


    FLITELite GEN II microprocessor receives information from two sensors, the rear sensor faces the mouth and the front sensor activated by the finger:
    • The rear sensor controls on and off functions, with a simple touch of the lip, the light turns on or off.
    • Battery life is protected by a computer controlled sixty minute auto-off.
    • The front sensor drives the brightness of the light. Touching the front sensor places the light to min bright to protect night vision, then slowly cycles to full bright.
    • The computer places this brightness setting into memory, and recalls the lighting level the next time the light is turned on.
    • Removing battery power clears the light memory.
    • The light is filtered through a special (and expensive) NVIS filter material on Night Vision Goggle compatible versions, and through a non-glare filter on Red, Green, and Soft-White versions.

    Internal components are the highest quality, FLITELite is made in America. Design flexibility is achieved by using a specially designed circuit board, the same material used in the Mars Lander. The latest in sensor technology is controlled by proprietary software. All of the components are sealed by a dielectric coating to protect your investment before being ultrasonically welded into the case.

    FLITELite is perfect for normal and emergency use. During normal operations FLITELite is great for reading charts and approach plates. FLITELite fills in dark spots, improves gauge visibility, and brightens up areas without light such as fuel selectors, etc...During emergency operations, FLITELite makes the electrical failure much less of an event. FLITELite has already logged several saves after electrical failures.

    FLITELite GEN II has a number of great improvements. One of them is that the angle on the light was changed from 0 degrees relative to the face of the light to 11.5 degrees. When the pilot adjusted the light to point directly ahead, some flexible and wire microphone booms were too short for some pilots heads. We tested, and found that by offsetting the light eleven degrees, we were able to put the light in the proper position for pilots with even the largest craniums.

    GEN II Control Demonstration



    Pick Your Light

    Choose the Micro, GEN II, Operator, Classic, or Fingerlight, Power Station, or MOLLE Light

    Choose Your Adapter

    Pick your lip light adapter and preferred battery pack - or just shoot us a mic picture and we can select for you.


    Mount your new kit on your mic boom, light up with a finger light or power station and OPERATE!